A Red-D-Arc customer based out of the UK was awarded three large offshore wind farm projects …all commencing simultaneously. This manufacturer was comfortable taking on so many large scale, specialized projects because they have a reliable, knowledgeable, tier 1 supplier capable of meeting all of their welding and weld automation equipment needs! Red-D-Arc was able to quickly accommodate all of the welding equipment requirements for the project, providing more than 150 welders and a variety of weld automation equipment. The equipment consisted of multi-operator welding paks, diesel welders, advanced power sources, wire feeders, submerged arc welding packages, and rotators.
Two Red-D-Arc technicians were assigned to the facility to install, service and maintain the equipment to minimize downtime. The facility allocated a permanent workshop and storage container for back-up equipment which could be used to quickly replace any equipment as necessary. With Red-D-Arc’s support, the customer was able to work on all three projects simultaneously and avoid lost time due to equipment breakdowns.
By guest Blogger Katarzyna K.
Katarzyna has an Msc in Materials Science and has worked in the oil and gas industry in jobs related to hydraulics, welding and the retrofitting of oil rigs.
Stainless steel is used extensively in the petrochemical industry due to its high resistance to severe conditions. When welding inox steels, the smallest details matter and have an impact on weld quality. The following are some tips for stainless steel pipe welding based on my oil rig repair experience:
During an oil rig repair project that involved 2205 duplex stainless steel pipe TIG welding, we could not achieve the required weld properties. Despite using the recommended filler metal with higher nickel content, compared to the base metal, and controlling the interpass temperature, the weld tensile strength was still too low. In order to reach the required weld quality we dug deeper and found a solution – (more…)
A project manager approached Red-D-Arc with an interesting challenge. Their power plant stack had a failing paint system which needed to be prepped for repainting in order to prevent further corrosion. They needed a method of prepping the surface of the 60 foot tall stack which could be performed without the use of scaffolding and would not produce any residual waste, since it might interfere with sensitive components.
Red-D-Arc’s Blasting Specialists suggested dry ice blasting (DIB). Dry ice blasting is an environmentally sustainable cleaning and surface preparation method. It uses dry ice pellets which requires absolutely no clean up, unlike traditional surface preparation methods like grit, HP water and chemicals. Not to mention, dry ice blasting is very fast, effective and inexpensive.
An oilfield equipment and vessel manufacturer in the United Arab Emirates approached Red-D-Arc for assistance with a large project. It was awarded to them at the last minute and was not their primary area of expertise. The requirement was to manufacture 25 large tanks with a timeframe of only one year. Each of the tanks was to be 5 meters in diameter by 25 meters long, manufactured using 16 millimeter thick material at a weight of approximately 45 tonnes.
The experienced Red-D-Arc Weld Automation team was able to immediately address all of the customer’s challenges. While other suppliers where insistent that the customer purchase the equipment, Red-D-Arc determined that long term rental would be their best option. This would avoid the time consuming process of acquiring CAPEX approval to purchase such a large amount of equipment and would further increase the profitability of the project. The manufacturer also had questions on how to avoid ovality and transverse movement of the sub-assemblies. Red-D-Arc experts were on-hand to provide the right advice and the right equipment to address these challenges.
The rental equipment included:
• 6x 10 tonne turning roll sets
• 10x 60 tonne drive rolls
• 47x 30 tonne and 60 tonne idler rolls
• 7x submerged arc packages with LT7 tractors and DC600 power sources
Red-D-Arc worked very closely with the company to ensure their success, providing comprehensive training and on-site assistance. After the successful completion of this project the company has become recognized in their market and are receiving new orders from similar customers in the industry. Furthermore, they anticipate being awarded “phase 2” of this project which is scheduled to begin in 2018.